Wood Beam Design Step by Step - Two Spans, a Point Load and a Simpson Hanger (NDS 2024)
1:14Published November 18, 2026Narrated, with captions and a full transcriptAlso on YouTube
How do you design a two-span wood beam with a point load? Enter the spans and the loads, pick the species, grade and size from the NDS 2024 Supplement tables, say how the edges are braced, and check flexure, shear, deflection and the end connection under every ASD load combination, including live load on one span at a time (ASCE 7-22 Section 4.3.3). This 74-second narrated tour does all of it in StructSuite, from an empty module to the printed report.
Transcript and details
About this video
The beam: two 12 ft spans, a 25 plf dead load, a 100 plf live load and a 900 lb point live load at 18 ft, Douglas Fir-Larch No. 2 4x12 from NDS Supplement Table 4A (Table 1B for the section), top edge continuously braced, bottom edge braced at points 12 ft apart. It passes at a moment D/C of 0.633 under D + L with the live load on span 2 only, shear 0.327, deflection 0.275 against L/360, and a Simpson Strong-Tie HUS412 face-mount hanger checks at 0.530 against the 1,046 lb end reaction.
The engineering behind the numbers
- Pattern live loading. On a continuous beam, live load on one span at a time can govern over the fully loaded case. Here the 2a arrangement (L on span 2 only) drives the positive moment, and span 1 lifts at its end support (3.8 lb uplift).
- Two bending strengths, one per face. The top edge is continuously braced, so CL = 1.000 for positive moment; the bottom edge, in compression over the interior support, is braced only at points 12 ft apart, so CL = 0.975 from NDS 2024 Section 3.3.3. With Fb = 900 psi and CF = 1.100, that gives Fb' = 990 psi (positive) and 965 psi (negative).
- Capacity against demand. With S = 73.83 in3, the positive capacity is 6,091 lb-ft against 3,855 lb-ft (0.633) and the negative 5,937 lb-ft against 2,535 lb-ft (0.427); the larger governs.
- The hanger. The governing ASD reaction goes to Simpson's Hanger Selector, normalized by the NDS load-duration factor to Simpson's own basis; the HUS412 is checked on its allowable download, 1,975 lb.
Questions this video answers
- How do you design a two-span wood beam?
- Enter spans and loads, pick species, grade and size from the NDS Supplement, set the bracing, and check flexure, shear and deflection under every ASD combination (bearing is an optional check in the same step).
- Why check live load on one span at a time?
- ASCE 7-22 Section 4.3.3: on a continuous beam, partial live loading can give larger moments than the fully loaded case.
- Why are there two allowable bending stresses?
- The beam stability factor CL depends on how each compression edge is braced, so positive and negative moment can get different CL.
- What does a continuously braced top edge do?
- It sets CL = 1.0 for positive moment (NDS 2024 Section 3.3.3).
- Where do the design values come from?
- NDS 2024 Supplement Table 4A (DF-L No. 2: Fb = 900 psi) and Table 1B for the section properties.
- How is a joist hanger checked?
- Against the governing ASD end reaction, normalized to the manufacturer's load-duration basis; here a Simpson HUS412 at 1,975 lb against 1,046 lb.
- Does the beam calculation go into a report?
- Yes. Each module becomes a section of one calculation report, with a cover sheet, contents and page numbers.
Transcript
The narration word for word, 172 words, from the video's own captions. Select a time to play from there.
Nine design modules - start a new wood beam
0:00Nine design modules, one calculation report. Let's start a brand-new wood beam. Two spans, 12 ft each.
Two spans, uniform and point loads (ASCE 7-22 Section 4.3.3)
0:10Loads next. Dead load, 25 plf. Live load, 100. And a 900-pound point load out on span two. Then we tick partial live loading. That is ASCE 7-22, Section 4.3.3. Keep an eye on it.
Species, grade and size from the NDS Supplement tables, and the bracing
0:24Douglas Fir-Larch, No. 2, a 4x12, straight out of NDS Table 4A. Bracing. The top edge is sheathed. The bottom edge is braced every 12 ft.
A Simpson Strong-Tie hanger, picked and checked
0:36It passes. Now the hanger. 82 Simpson options, and we pick the HUS412. It carries the 1,046-pound end reaction at 0.53.
Every check worked out - flexure per NDS 2024
0:45Every check is worked out. Moment governs at 0.633, with live load on span two only. Not the fully loaded beam. And two CL values: 1.0 on top, 0.975 on the bottom.
Load combinations, diagrams and the printed report
0:56Every load combination gets its own diagrams. Pick one, and the shear, moment and deflection redraw. See that tiny uplift on the left? That is span two lifting span one. And the report builds itself. StructSuite.com. Free to use, no account.
